
Editorial illustration.
When video calls freeze in the upstairs study but stream smoothly beside the router, it is tempting to buy a mesh kit straight away. Hold off for a few minutes. The same symptom can come from a weak signal, one misbehaving device, interference, or a slow broadband connection. Each has a different fix, and a new access point will not repair a problem at the modem or internet provider.
This short test helps you locate the weak link before spending money.
Summary
- Compare the same device near the router and in the problem room, then compare a second device in that room.
- If everything slows only in one place, test router position and obstacles before changing settings.
- If every room and device is slow, check the broadband connection or provider; if one device is slow everywhere, inspect that device.
- Move one thing at a time and repeat the same test so you know which change helped.
First, make the comparison fair
Choose one simple test you can repeat, such as a video call, opening the same website, or a speed test from the same app. Run it on the same phone or laptop, at roughly the same time, once near the router and once in the problem room. Note whether the issue is buffering, disconnections, or simply a lower speed. A single speed-test number is less useful than the pattern.
If possible, connect a laptop to the router with an Ethernet cable and repeat the test. This separates the incoming internet connection from the wireless link. If the wired connection is also poor, Wi-Fi placement is unlikely to be the main cause. If wired is stable but the room is not, focus on the local wireless path.
Do not compare a video stream on one device with a speed test on another and call the difference a router fault. Background downloads, VPNs, and device age can change the result. Pause large downloads and keep the test device consistent.
A five-step diagnosis
1. Check whether it is one device or one location
In the problem room, test a second device. Then take the original device beside the router. If only one device struggles in both places, restart it, check whether it has a software update waiting, and confirm it is not connected to a separate guest network or VPN. If several devices struggle in that room but work near the router, you have evidence of a coverage or interference issue.
If all devices are slow in every room, check the modem and router status lights and run the wired comparison. A provider fault or an overloaded connection is more plausible than a single room’s wall blocking the signal. Google’s Nest Wi-Fi troubleshooting guidance also recommends checking the internet service when test results are below expectations.
2. Move the router before changing its settings
Routers often end up in a cabinet, behind a television, under a desk, or beside the modem at the far end of a house. That is convenient for cables, but poor for coverage. Put the router in an open, raised position closer to the centre of the home if the cable allows it. Keep it away from large metal objects and dense walls where possible.
Change only the position, then repeat the same test. Even a move of a few feet can show whether a wall or furniture is part of the problem. Google recommends placing compatible Wi-Fi points in the open and avoiding dense obstacles; its advice is specific to Nest and Google Wifi, but the basic principle is useful for diagnosing any home layout.
3. Treat the Wi-Fi band as a trade-off
Many routers offer 2.4 GHz and 5 GHz networks; newer equipment may also offer 6 GHz. A higher-frequency band can provide more capacity and speed nearby, while walls and distance can make it less useful at the far end of the house. The device and router must both support the band, too.
If your router shows separate network names, briefly test the device on each available band from the problem room. Do not rename networks or disable a band as your first step. Some smart-home devices only support 2.4 GHz, and forcing every device onto one band can create a different headache. Apple’s router settings guidance recommends enabling the bands a router supports and leaving channel selection on automatic for most homes.
4. Look for interference and weak mesh placement
A room may be slow only at certain times. In an apartment block, nearby networks share radio space; appliances and other wireless devices can also interfere. Try a short test with a microwave or cordless device switched off, then test again. Do not conclude that a specific appliance is responsible unless the result repeats.
A mesh point should sit between the router and the weak room, where it still receives a good connection. Hiding it in the room with the worst signal can simply give it a weak signal to repeat. If your system has a mesh test, use it after each move. Google’s mesh placement guide describes checking the link between the primary point and additional points.
5. Decide whether you need more hardware
If moving the router helps but cannot cover the whole home, a wired access point is usually the most predictable extension when Ethernet cabling is practical. Mesh is convenient when running cable is difficult, but each wireless hop depends on a healthy link back to the router. A basic repeater may help in a small dead zone, though it can reduce available capacity and add another network name or roaming quirk.
Before buying, mark the weak room on a simple floor plan and identify the nearest good-signal location. Ask the installer or retailer about return terms and whether the equipment works with your current router. Buy for the measured problem, not the biggest advertised speed figure.
Example: a study at the back of a terrace house
Suppose a laptop gets a steady call beside the router but drops audio in the upstairs study. A phone in the same study has the same trouble, while both work downstairs. That points away from a single faulty laptop and toward the route through the floor and walls. Raising the router and moving it into an open central spot improves both devices; if the study remains weak, a mesh point placed near the stair landing is a sensible test. If instead both devices also fail beside the router and a wired laptop is slow, contact the internet provider before adding mesh equipment.
For the related case where the network works but one website does not, use our guide to find the request making a website slow. If devices cannot resolve site names at all, our DNS troubleshooting guide covers the next checks.
Mistakes that waste time
- Changing several router settings at once. You will not know which change fixed or worsened the connection.
- Putting a mesh point in the dead zone. It needs a good link to the main router, not just proximity to the device.
- Assuming a fast plan guarantees a strong signal. The broadband plan affects the connection into the home; walls and interference affect the wireless link to a room.
- Buying hardware before comparing devices and locations. That can leave the original cause untouched.
- Changing channels to a random number from a forum. Neighbouring networks and local conditions differ. Start with automatic channel selection unless you have a measured reason to tune it.
My Take
The most useful question is not “How fast is my Wi-Fi?” but “Where does the problem start, and does it follow the room or the device?” That small distinction prevents a lot of unnecessary shopping. If the tests point to a coverage gap, then improve placement or add an access point. If they point upstream, give your provider evidence from a wired test.
Bottom Line
Run the same test in two places and on two devices before you change anything. A room-only problem calls for a placement and coverage check; an everywhere problem calls for a broadband check. Make one change, repeat the test, and only then decide whether new hardware is justified.